23. Which of the following techniques is not correct in producing X-rays?
(A) bombardment of a metal target with a beam of high-energy electrons
(B) use of a radioactive source to excite a metal target
(C) excitation of a metal target through chemical reactions
(D) from a synchrotron radiation source
(E) irradiation of a metal target with a primary X-ray source

19. When considering the propagation of uncertainty with a calibration curve from linear regression, which of the following approaches or conditions does not help narrow down the uncertainty (Sx) of the unknown concentration [X]? (A) to achieve a greater slope for the calibration curve (B) to have more data points for the calibration line (C) to increase the number of replicate measurements of the unknown (D) the signal or response of the unknown to be at the far ends of the calibration line (E) a correlation coefficient closer to unity

20. Which of the following statements regarding detection limits (D.L.) are false: (1) Only ~1% of measurements of a blank are expected to exceed theD.L. (2) If the analyte concentration is right at the D.L., then one is only 50% confident to say that the sample does contain analyte. (3) If the analyte concentration is right at theD.L., then one is 99% confident to say that the sample does contain analyte. (4) Measurements showing results below D.L. can suggest the sample does not contain analyte. (5) The probability of being false positive is ~1% for samples containing no analyte. Your answer: (A) 1,2,5 (B)1, 2, 4 (C)3,5 (D)2, 5 (E) 3,4

21. Why is source modulation needed in atomic absorption spectroscopy? (1) to create a double-beam configuration for the spectrometer, (2) to separate the emission signal of the analyte in the flame from the emission of the fuel and oxidant in the flame, (3) to create a AC type of signal for the flame emission, (4) to create a DC type of signal for the light source, (5) to create a AC type of signal for the light source. Your answer: (A)1,2,4 (B)1,5 (C)1,4 (D)1,2,3 (E)5

22. In the ICP-MS technique which of the following ionization method is utilized? (A) Electrospray (B) MALDI (C) Electron impact (D) High temperature in an inert atmosphere (E) Reaction with Ar atoms

24. Why is the graphite furnace AA technique more sensitive than the flame AA technique for most of the transition metals? (1) the sample amount is larger for furnace AA； (2) the average residence time of atoms in furnace is much longer than in the open flame； (3) the steady-state concentration of atoms in the flame is much lower than in the furnace； (4) the flame temperature is higher than furnace's； (5) the detector of furnace AA is more sensitive. Your answer: (A)2,3,5 (B)2,3 (C)4,5 (D)1,4,5 (E)3,4

25. The interferometer is used in FT-IR (1) to act like a grating in a monochromator, (2) to scan wavelengths from low to high, (3) to facilitate FT because the IR frequencies are too high to be acquired by average-cost electronics, (4) to resolve IR frequencies into a series of sine and cosine functions, (5) to produce an identical time-domain spectrum of much lower frequencies. Your answer: (A) 1,2 (B)1, 2,4 (C)3,4 (D)3, 4,5 (E)5

201. 移動式起重機應具有於行駛方向為水平且堅固地面上，不致翻倒之左右安 定度，該左右方向傾斜度是多少？ (A)5 度 (B)10 度 (C)20 度 (D)30 度 。

202. 移動式起重機用於保持停止狀態之制動系統，應具有使起重機於無荷重狀 態，停止於地面斜度為多少？ (A)八分之一 (B)七分之一 (C)六分之一 (D)五分之一 。

203. 制動轉矩值應為承載相當於額定荷重時，起重機吊升裝置最大轉矩值不低 於 (A)1.8 倍 (B)1.7 倍 (C)1.6 倍 (D)1.5 倍 。

204. 制動力使用人力操作者，應設置擋齒裝置或擋鍵，其手動制動力應小於 (A)50kg (B)40kg (C)30kg (D)20kg 。